Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

Multibody Contact Analysis of an Rzeppa CV-Joint

L. Armellin[1], F. Gatelli[1], and G. Tanghetti[1]

[1]R&D Department, Metelli S.p.A., Cologne, BS, Italy

Ball joints are widely used in many applications. This paper describes the contact and kinematic analysis of an Rzeppa type constant-velocity joint (CV-joint). Starting from a conveniently simplified 3D model, at fixed joint angle of 45°, a CV-joint made of all “generic steel” components has been studied. Considering only a “perfect” geometry (i.e. not affected by ...

Thermal and Material Flow Modelling of Friction Stir Welding Using COMSOL

H. Schmidt[1,2], and J. Hattel[1]
[1]Technical University of Denmark, Kgs. Lyngby, Denmark
[2]HBS Engineering, Frederiksberg, Denmark

Two friction stir welding models are presented – a global thermal model using the temperature dependent heat source and a local material flow and heat generation model allowing for detailed investigation of different contact conditions. The two models are coupled into a larger local-global model. The flow model includes frictional dissipation from the contact between the work piece and the ...

Modeling the Thermally Induced Curvature of Multilayer Coatings with COMSOL MultiphysicsTM

H. Conrad[1], T. Klose[2], T. Sandner[2], D. Jung[1], H. Schenk[2], and H. Lakner[1,2]
[1]Semiconductor and Microsystems Technology Laboratory, Technische Universität Dresden, Germany
[2]Fraunhofer Institute for Photonic Microsystems Dresden, Germany

Within this paper the so called “birth and death” method is demonstrated in use with COMSOL Multiphysics®. With this method the free and reactionless movement of a solid structure on deformed geometries and the activation of this solid structure at later simulation steps is possible. For demonstrating the benefit, this method was applied to simulate the thermal induced ...

Modeling of Ultrasonic Fatigue-Life Testing Machine

D. Dimitrov[1], V. Mihailov[1], B. Kostov[1]
[1]Technical University of Varna, Varna, Bulgaria

Usually fatigue-life tests of materials are long, time-consuming and expensive. With the development of high power piezoceramic actuators nowadays it is possible to provide at very high cycles 10e10 fatigue tests (VHCF) for reasonable times, at high frequency. The ultrasonic fatigue machine consists of piezoceramic transducer, booster, horn and specimen made of tested material. System works in ...

Finite Element Analysis of Pipes Considering the Effects of Stress Concentration Due to Dents

S.C. de Oliveira[1], E.P. de Deus[2], and A.M. Mont'Alverne[2]
[1] Funcap/CNPq, CE, Brazil
[2] Universidade Federal do Ceara, Fortaleza, CE, Brazil

This paper presents a numerical analysis of indented pipes based on the Finite Element (FE) within the framework of COMSOL Multiphysics. Numerical models using two-dimensional solid plane strain elements are evaluated. Geometric nonlinear analysis, nonlinear isotropic hardening material and contact were also incorporated into the models. The numerical models are calibrated by using an ...

Implementation of the Finite Isotropic Linear Cosserat Models based on the Weak Form

J. Jeong[1], and H. Ramezani[2]
[1]Ecole Speciale des Travaux Publics du Batiment et del’Industrie(ESTP), Cachan, France
[2]Ecole Polytechnique de l’Universite d’Orleans CNRS/CRMD, Orleans, France

The Cosserat models fall into the group of the extended continuum media. They are capable of treating the size effects (characteristic length) in a natural manner using six material moduli for the isotropic elastic cases instead of two (and) for the classical continuum mechanics. This model involves two constitutive laws corresponding to two kinds of balance equation. The first one handles the ...

Uncertainty Analysis, Verification and Validation of a Stress Concentration in a Cantilever Beam

S. Kargar, and D. Bardot
University of Alabama, Huntsville, AL, USA

In this paper we compare the results from a bending cantilever beam experiment with the theoretical values and COMSOL finite element simulation results. In the experiment a simple cantilever beam with a hole is loaded at the end. Measurements are recorded by four strain gauges mounted on the beam, three near the hole and one at a location where the nominal stress is equivalent to that of a ...

Load Cell Design Using COMSOL Multiphysics

A. Marchidan[1], T. Sullivan[1], J. Palladino[1]
[1]Trinity College, Hartford, CT, USA

COMSOL Multiphysics was used to design a binocular load cell. A three-dimensional linear solid model of the load cell spring element was studied to quantify the high-strain regions under loading conditions. The load cell was fabricated from 6061 aluminum, and general purpose Constantin alloy strain gages were installed at the four high-strain regions of the spring element. The four gages were ...

A Multiphysics Approach to the Modeling of Biological Prosthetic Heart Valves

A. Avanzini[1], D. Battini[1], M. Berardi[1]
[1]Università degli Studi di Brescia, Brescia, Italy

The complex behavior of biological prosthetic heart valves was simulated. A multiphysics computational approach was adopted using different modules of COMSOL Multiphysics: the LiveLink(TM) interface was used to exchange the valve geometry with CAD, Structural Mechanics Module to set loads, boundary conditions and implement anisotropic hyper-elastic constitutive laws for leaflet tissue, PDE to ...

A Numerical Model for Transient Heat Conduction in Semi-Infinite  Solids Irradiated by a Moving Heat Source

N. Bianco[1], O. Manca[2], S. Nardini[2], and S. Tamburrino[2]
[1]Dipartimento di Energetica, Termofluidodinamica applicata e Condizionamenti ambientali, Università degli Studi Federico II, Napoli, Italy
[2]Dipartimento di Ingegneria Aerospaziale e Meccanica, Seconda Università degli Studi di Napoli, Aversa (CE), Italy

A numerical analysis on transient three-dimensional temperature distribution in a semi-infinite solid, irradiated by a moving Gaussian laser beam, is carried out numerically by means of the code COMSOL Multiphysics. The investigated workpiece is simply a solid. A laser source is considered moving with constant velocity along the motion direction. The convective heat transfer on the upper surface ...