Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

Strong Magnetic Field and Its Application

Y. Song
Huazhong University of Science and Technology, Wuhan, China

High magnetic field research has yielded fruitful results. Since 1913, associated with the magnetic field there are 19 Nobel Prizes, including a prize for medicine, five chemistry prizes, and 13 physics prizes. In recent years, the international community under the conditions of strong magnetic field is very active in scientific research, involving many disciplines such as physics, chemistry, ...

Design and Analysis of Implantable Nanotube Based Sensor for Continuous Blood Pressure Monitoring

M. Silambarasan, T. Prem Kumar, M. Alagappan, and G. Anju
PSG College of Technology
Coimbatore
Tamil Nadu, India

The present work aims to develop a blood pressure sensor using MEMS/NEMS technology. A normal blood pressure detector is used externally, but this work mainly aims for designing an implantable nanotube based sensor for continuous monitoring of blood pressure. The use of COMSOL Multiphysics 4.1 acts as a good platform to develop a nano tube based sensor design by using the MEMS module. The ...

Air Convection on a Micro Hotplate Gas Sensor

S. Gidon[1], M. Brun[1], S. Nicoletti[1], P. Barritault[1]
[1]Commissariat Energie Atomique, LETI, Minatec Campus, Grenoble, France

Monitoring of indoor CO2 concentration is of particular interest to detect room occupancy in order to optimize power consumptions of building. One approach to monitor the indoor CO2 concentration is to use optical detection using specific absorption lines of CO2 molecules in the infrared domain close to 4.2 µm. Such optical sensors include a detector, typically a micro-bolometer, an IR source ...

Design of an Electrodynamically Actuated Microvalve Using COMSOL Multiphysics® and MATLAB®

M. Williams, J. Zito, J. Agashe, A. Sopeju, and D. Arnold
University of Florida, Gainesville, USA

This paper describes the design of a normally closed, electrodynamic microvalve.  Magnetic forces between a permanent magnet in the valve cover and a soft magnet in the valve seat hold the valve closed.  The combination of electrodynamic actuation and a mechanical restoring spring are used to open the valve.  A device model and a design optimization strategy using COMSOL ...

A Modular Platform for Cell Characterization, Handling, and Sorting by Dielectrophoresis

S. Burgarella[1], B. Dell’Anna[2], V. Perna[1], G. Zarola[2], and S. Merlo[2]

[1]STMicroelectronics, Agrate Brianza, MI, Italy
[2]Dipartimento di Elettronica, Università degli Studi di Pavia, Pavia, Italy

Dielectrophoresis (DEP) is a method for cell manipulation without physical contact in lab-on-chip devices, since it exploits the dielectric properties of cells suspended in a microfluidic sample, under the action of locally generated high-gradient electric fields. The DEP platform that has been developed offers an integrated solution for customizable applications. Several functional units, ...

Modeling and Simulation of the Rapid and Automated Measurement of Biofuel Blending in a Microfluidic Device under Pressure Driven Flow using COMSOL Multiphysics®

Sanket Goel[1], Venkateswaran PS[1], Rahul Prajesh[2], Ajay Agarwal[2]
[1]University of Petroleum & Energy Studies, Bidholi, Prem Nagar, Dehradun, India
[2]CSIR - Central Electronics Engineering Research Institute,(CSIR-CEERI) Pilani, India

• Real-time detection and monitoring of bio-fuel blend-ratio and adulterated automobile fuels by a reproducible micro-fabrication process in a cost-and-time efficient manner. • COMSOL Multiphysics® simulations and modelling of Viscosity based Laminar Flow inside a Y-shaped Micro-fluidic Device. • Design and Fabrication of a polymer Y-shaped Micro-fluidic Device to work as Micro-Viscometer for ...

Simulations of Micropumps Based on Tilted Flexible Structures - new

M. J. Hancock[1], N. H. Elabbasi[1], M. C. Demirel[2]
[1]Veryst Engineering, LLC., Needham, MA, USA
[2]Pennsylvania State University, University Park, PA, USA

Pumping liquids at small scales is challenging because of the principle of reversibility: in a viscous regime, the flow streamlines through a fixed geometry are the same regardless of flow direction. Recently we developed a class of microfluidic pump designs based on tilted flexible structures that combines the concepts of cilia (flexible elastic elements) and rectifiers (e.g., Tesla pump). We ...

A Comparison of Mass Reduction Methods for Silicon-on-Oxide (SOI)-based Micromirrors

H. J. Hall [1], L. A. Starman [1],
[1] Sensors Directorate, Air Force Research Laboratory, Wright-Patterson AFB, OH, USA

Beam steering and adaptive optics micromirror applications commonly demand optically flat surfaces with minimal mass. When reflective coatings (usually metallic Au or Al) are applied to micromirror surfaces in order to meet optical reflectivity requirements the resulting film stress (usually tensile) can be substantial. The mass of the mirror can be a limiting factor in the dynamic performance. ...

Design of Novel Recirculation System for Slow Reacting Assays in Microfluidic Domain

N.N. Sharma, and A. Tekawade
Mechanical Engineering Group, Birla Institute of Technology & Science, Pilani, Rajasthan, India

A simple design for a microfluidic flow system for use in mixing or reacting assays with limited sample availability has been proposed and analyzed using COMSOL\'s multiphysics simulation package. The design is based on differential electroosmotic flow concept which has facilitated a number of interesting flow phenomena in micro-domains. For an average potential drop of about 86 kV/m in the ...

Design of MEMS based Polymer Microphone for Hearing Aid Application

V. S. Nagaraja[1], Ramanuja H. S.[1], Deepak K[1], S. L. Pinjare[1]
[1]Electronics and Communication Engineering, Nitte Meenakshi Institute of Technology, Bangalore, Karnataka, India

In this work, a MEMS based condenser microphone [1,2] using Polyimide as the diaphragm has been designed. The microphone structure has a backplate placed on top of the diaphragm. The backplate and the diaphragm are made up of polyimide. The two polyimide plates are separated by air gap which is achieved by using Aluminium as a sacrificial layer in between, which is etched away to create the air ...