Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

COMSOL Simulations for Steady State Thermal Hydraulics Analyses of ORNL’s High Flux Isotope Reactor

P.K. Jain[1], V.B. Khane[2], J.D. Freels[1]
[1]Oak Ridge National Laboratory, Oak Ridge, TN, USA
[2]Missouri University of Science and Technology, Rolla, MO, USA

Simulation models for steady state thermal hydraulics analyses of ORNL’s HFIR have been developed using COMSOL. A single fuel plate and coolant channel of each type of HFIR fuel element was modeled in three dimensions. The standard k-? turbulence model was used in simulating turbulent flow with conjugate heat transfer. The COMSOL models were developed to be fully parameterized to allow ...

COMSOL-based Simulations of Criticality Excursion Transients in Fissile Solution

C. Hurt[1], P. Angelo[2], R. Pevey[1]
[1]Department of Nuclear Engineering, University of Tennessee, Knoxville, TN, USA
[2]Y-12 National Security Complex, Safety Analysis Engineering, Oak Ridge, TN, USA

Simulation of criticality accident transients offers the ability to confirm understanding of critical configurations, bound accident scenarios and aid comprehensive emergency planning. Computational ability to recreate excursion power histories in fissile solution is sought due to the predominance of solutions in process criticality accidents. Applicable solution transient physics methodologies ...

The Hygro-Thermal Improvement of a Mounting System to Fasten Roof Workmen to Flat Roofs - new

H. L. Schellen[1]
[1]Eindhoven University of Technology, Eindhoven, The Netherlands

A Dutch firm manufactures a mounting system to fasten roof workmen to the roof of a flat roof building to prevent them from falling down from the roof. The system is mounted to the flat roof afterwards, i.e. after the completion of the thermal insulated roof. Because of the mechanical strength and stiffness properties of the system, it is manufactured using (stainless) steel. The steel, ...

Numerical Simulation of Warm-Air Drying of Mexican Softwood (Pinus Pseudostrobus)

S. Sandoval Torres[1], E. Hernández-Bautista[1], J. Rodríguez-Ramírez[1], A. Carrillo Parra[2]
[1]Instituto Politécnico Nacional, CIIDIR, Oaxaca, Mexico
[2]Facultad de Ciencias Forestales, Universidad Autónoma de Nuevo León, Linares, N.L. México

In this work, the numerical simulation of Mexican softwood (Pinus pesudostrobus) drying is presented by solving a physics-based model. The model was developed by considering the heat and mass transport and the representative elementary volume, which involves the solid, liquid and gas phases. We solved a system of partial differential equations by numerical factorization in COMSOL Multiphysics 3 ...

Thermal Simulation and Package Investigation of Wireless Gas Sensors

A. Paoli[1], L. Seminara[2], D.D. Caviglia[1], A. Garibbo[2], and M. Valle[1]

[1]Department of Biophysical and Electronic Engineering, University of Genova, Genova, Italy
[2]SELEX Communications S.p.A., Genova, Italy

Gas sensor arrays based on metal oxides operating at high temperature are commonly used in many application fields. They can operate on different principles and each sensor may show very different responses to the individual gases in the environment. Data coming from the array can be merged for reliable gas detection. One point which is common to the different sensors types is that the ...

Solution of Inverse Thermal Problem for Assessment of Thermal Parameters of Engineered H2 Storage Materials

I. Fedchenia, and B. van Hassel
United Technologies Research Center
East Hartford, CT

Materials based H2 storage systems for light duty vehicles need to meet challenging performance targets that have been developed by the FreedomCAR and Fuel Partnership. On-board reversible metal hydrides are typically integrated with heat transfer surfaces, e.g. in fin and tube heat exchangers, in order to reject the heat of H2 absorption at a high rate which is set by the refueling time ...

Heat Drain Device on Ultrasound Imaging Probe - new

G. Vigna[1], L. Spicci[1]
[1]Esaote SPA, Florence, Italy

Self-heating is a problem to consider for Ultrasound Imaging probes. Since the probe is in contact with the skin, it’s necessary to find a solution to lower the front face temperature in order to avoid patient discomfort, even at the most demanding operating condition. One solution consists in the design of a device that drains the heat from the front to the rear of the transducer, where a ...

Microwave Heating at the Grain Level

S. Lefeuvre[1], and O. Gomonova[2]
[1]Eurl Creawave, Toulouse, France
[2]Siberian State Aerospace University, Krasnoyarsk, Russia

The microwave heating and processing of heterogeneous material is usually simulated using a set of coupled PDE equations in an homogeneous medium. Nowadays it is possible to describe more accurately the process with a suitable description of the heterogeneities that is at the grain level. Many authors work with spheres (circles) to represent the grains but it is difficult to achieve an ...

Modelling of the Dynamical Fluorescent Micro-Thermal Imaging Experiment on the Heat Diffusion in the La5Ca9Cu24O41 Spin Ladder Compound - new

E. Khadikova[1], F. de Haan[1], P. H. M. van Loosdrecht[2]
[1]Zernike Institute for Advanced Materials, University of Groningen, Groningen, The Netherlands
[2]Department of Physics, University of Cologne, Köln, Germany

The dynamical fluorescent micro-thermal imaging (FMI) experiment has been used to investigate the phonon-magnon interaction in the 1D Heisenberg antiferromagnet La5Ca9Cu24O41. This material shows highly anisotropic heat conductivity due to the efficient magnetic heat transport along the spin ladders in the compound carried by magnetic excitations (magnons). To extract information on the phonon ...

Modeling a Cooling Skylight

M. Fält, and R. Zevenhoven
Thermal and Flow Engineering Laboratory, Department of Chemical Engineering
Åbo Akademi University
Turku
Finland

Air-conditioning produced by traditional vapor compression cycle is an energy demanding operation. By using passive cooling methods is it possible to avoid, or at least reduce, the need for vapor compression cooling. A passive radiative cooling method could be a three windowed skylight, filled with a greenhouse gas. Earlier modeling of such a skylight has shown promising results, and work has ...

1 - 10 of 552 First | < Previous | Next > | Last