Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.

Surface Plasmon Resonance

J. Crompton[1], S. Yushanov[1], L.T. Gritter[1], K.C. Koppenhoefer[1]
[1]AltaSim Technologies, Columbus, OH, USA

The resonance conditions for surface plasmons are influenced by the type and amount of material on a surface. Full insight into surface plasmon resonance requires quantum mechanics considerations. However, it can be also described in terms of classical electromagnetic theory by considering electromagnetic wave reflection, transmission, and absorption for the multi-layer medium. The two commonly ...

Earth Pressure as a Boundary Condition to Bridge Piers and Abutments

M. Quinn[1], D. Whitlow[1], O.D.S. Taylor[1], M.H. McKenna[1]
[1] Engineer Resource and Development Center, United States Army Corps of Engineers, Vicksburg, MS, USA

Bridge piers and abutments makeup the bridge substructure and transmit loads from the superstructure to the bridge foundation material (Figure 1). The bridge abutment serves three purposes: to provide vertical support to the bridge superstructure where the bridge ends, to connect the bridge with the approach roadway, and to retain roadway base materials. There are several types of abutment ...

Natural Convection Driven Melting of Phase Change Material: Comparison of Two Methods

D. Groulx[1], F. Samara[1], P.H. Biwole[2]
[1]Department of Mechanical Engineering, Dalhousie University, Halifax, NS, Canada
[2]Department of Mathematics and Interactions, University of Nice Sophia-Antipolis, Nice, France

Design of latent heat energy storage systems (LHESS) requires knowledge of heat transfer processes within them, as well as the phase change behavior of the phase change material (PCM) use. COMSOL Multiphysics can be used to model (LHESS). Natural convection plays a crucial role during the charging phase of the LHESS, and methods to incorporate this heat transfer mode within COMSOL simulation ...

Simulation of Acoustic Energy Harvesting Using Piezoelectric Plates in a Quarter-Wavelength Straight-Tube Resonator

B. Li[1], J.H. You[1]
[1]Southern Methodist University, Dallas, TX, USA

An acoustic energy harvesting mechanism at low frequency (~200 Hz) using lead zirconate titanate (PZT) piezoelectric cantilever plates placed inside a quarter-wavelength straight-tube resonator has been studied using COMSOL Multiphysics 4.3 and compared with experimental data. When the tube resonator is excited by an incident wave at its acoustic eigenfrequency, an amplified acoustic resonant ...

Load Cell Design Using COMSOL Multiphysics

A. Marchidan[1], T. Sullivan[1], J. Palladino[1]
[1]Trinity College, Hartford, CT, USA

COMSOL Multiphysics was used to design a binocular load cell. A three-dimensional linear solid model of the load cell spring element was studied to quantify the high-strain regions under loading conditions. The load cell was fabricated from 6061 aluminum, and general purpose Constantin alloy strain gages were installed at the four high-strain regions of the spring element. The four gages were ...

Optimization of Artificial Diffusion Stabilization Techniques and Corresponding Mesh Density Distribution in Drift Dominated Transport of Diluted Species

J. Jadidian[1], M. Zahn[1], N. Lavesson[2], O. Widlund[2], K. Borg[2]
[1]Massachusetts Institute of Technology, Cambridge, MA, USA
[2]ABB Corporate Research, Västerås, Sweden

This paper presents an optimized combination of artificial diffusion techniques to stabilize a drift dominated streamer discharge model which includes COMSOL Multiphysics’ Transport of Diluted Species modules for positive ion, negative ion, and electron charge densities, coupled through the Electrostatic module. A Thermal Conduction and Convection module is responsible for the heat transfer in ...

Numerical Modeling of Pit Growth in Microstructure

S. Qidwai[1], N. Kota[2], V. DeGiorgi[1]
[1]Naval Research Laboratory, Washington, DC, USA
[2]Science Applications International Corporation, Washington, DC, USA

Pitting corrosion is a complex phenomenon where rates of: i) chemical reactions, ii) diffusion of various species involve in those reactions, and iii) species dissolution at the metal-electrolyte interface are fully dependent on each other, except under special conditions or assumptions. One set of such conditions is that: a) there are no species concentration gradients due to the rapid mixing ...

Analysis of Superheater Tubes with Mutual Irradiation as Applied to a Solar Receiver Steam Generator

N. Lemcoff[1], S. Wyatt[2]
[1]Rensselaer Polytechnic Institute, Hartford, CT, USA
[2]Alstom Power, Windsor, CT, USA

The objective of this paper is to analyze the temperature variations within a superheater tube of a solar receiver steam generator. The tube is heated by concentrated, collimated solar irradiation with major cooling by an internal steam flow. The influence of heat loss by radiation, internal convection, and conduction are considered. Analytical models are obtained for an isolated tube, and the ...

Pulsed Eddy Current Probe Development to Detect Inner Layer Cracks Near Ferrous Fasteners Using COMSOL Modeling Software

V. Babbar[1], P. Whalen[1], T. Krause[1]
[1]Department of Physics, Royal Military College of Canada, Kingston, ON, Canada

Surface breaking cracks in conductive structures can be detected by conventional eddy current techniques. However, it is very difficult to detect inner layer defects in multilayered conductive structures either by conventional eddy current or ultrasonic methods. The transient/pulsed eddy current (PEC) technology can potentially overcome these limitations and is being developed for detection of ...

EM Simulation of a Low-Pass Filter Based on a Microstrip Defected Ground Structure

J.E. Rayas-Sánchez[1], J. Aguilar-Torrentera[1], Z. Brito-Brito[1], J.C. Cervantes-González[2], C.A. López[2]
[1]Universidad Jesuita de Guadalajara, Tlaquepaque, Jalisco, Mexico
[2]Intel Guadalajara Design Center, Tlaquepaque, Jalisco, Mexico

We perform EM simulations of a low-pass microstrip filter consisting of a cross-junction open stub and two unit sections implemented as defected ground structures (DGS). The defect introduced by unit sections corresponds to an etched lattice on the copper backside ground plane. The filter presents wide and deep attenuation characteristics in the stopband. Different model implementations were ...

1 - 10 of 143 First | < Previous | Next > | Last